Group: DynoMotion	Message: 9710	From: Wcarrothers Yahoo	Date: 6/27/2014
Subject: Fet temp snap amps

Hello.

I know this is a loaded question as results will vary. But I've experimented alot with fets in power modules and was wondering what temps are typical reported for the snap amp.

Perhaps what is considered a good range and what is considered the you are messing things up

What are the limits for when the fans activate? Just so I know what it is thinking

So far I've been around 30c when things are active

On Jun 27, 2014, at 9:16 AM, "eric@

Group: DynoMotion	Message: 9715	From: TK	Date: 6/27/2014
Subject: Re: Fet temp snap amps

Hi Bill,

The SnapAmp Fans turn on at 40C and over temp faults at 70C.

Regards
TK

On Jun 27, 2014, at 7:46 AM, "Wcarrothers Yahoo wcarrothers@... [DynoMotion]" <DynoMotion@yahoogroups.com> wrote:

Hello.

I know this is a loaded question as results will vary. But I've experimented alot with fets in power modules and was wondering what temps are typical reported for the snap amp.

Perhaps what is considered a good range and what is considered the you are messing things up

What are the limits for when the fans activate? Just so I know what it is thinking

So far I've been around 30c when things are active

B

On Jun 27, 2014, at 9:16 AM, "eric@

Group: DynoMotion	Message: 9716	From: Wcarrothers Yahoo	Date: 6/27/2014
Subject: Re: Fet temp snap amps

Good to know. Guessing the fault would open all fets and stop the system

On Jun 27, 2014, at 2:11 PM, "TK tk@... [DynoMotion]" <DynoMotion@yahoogroups.com> wrote:

Hi Bill,

The SnapAmp Fans turn on at 40C and over temp faults at 70C.

Regards
TK

On Jun 27, 2014, at 7:46 AM, "Wcarrothers Yahoo wcarrothers@... [DynoMotion]" <DynoMotion@yahoogroups.com> wrote:

Hello.

I know this is a loaded question as results will vary. But I've experimented alot with fets in power modules and was wondering what temps are typical reported for the snap amp.

Perhaps what is considered a good range and what is considered the you are messing things up

What are the limits for when the fans activate? Just so I know what it is thinking

So far I've been around 30c when things are active

B

On Jun 27, 2014, at 9:16 AM, "eric@

Group: DynoMotion	Message: 9717	From: TK	Date: 6/27/2014
Subject: Re: Fet temp snap amps

Hi Bill,

Yes over temp turn off all FETS.

Regards
TK

On Jun 27, 2014, at 11:14 AM, "Wcarrothers Yahoo wcarrothers@... [DynoMotion]" <DynoMotion@yahoogroups.com> wrote:

Good to know. Guessing the fault would open all fets and stop the system

B

On Jun 27, 2014, at 2:11 PM, "TK tk@... [DynoMotion]" <DynoMotion@yahoogroups.com> wrote:

Hi Bill,

The SnapAmp Fans turn on at 40C and over temp faults at 70C.

Regards
TK

On Jun 27, 2014, at 7:46 AM, "Wcarrothers Yahoo wcarrothers@... [DynoMotion]" <DynoMotion@yahoogroups.com> wrote:

Hello.

I know this is a loaded question as results will vary. But I've experimented alot with fets in power modules and was wondering what temps are typical reported for the snap amp.

Perhaps what is considered a good range and what is considered the you are messing things up

What are the limits for when the fans activate? Just so I know what it is thinking

So far I've been around 30c when things are active

B

On Jun 27, 2014, at 9:16 AM, "eric@